Engineering resources

Shop math, ready to print.

The charts our machinists keep at the bench, the calculators they reach for, and the documents buyers ask for. Look it up here, or print the card and hang it by the machine.

Sheet gauge.

Gauge to thickness, four materials.

Manufacturers' Standard Gauge for carbon and galvanized steel, U.S. Standard for stainless, Brown and Sharpe for aluminum. Inches and millimeters.

Sheet gauge chart

Gauge to decimal inches, mm below

GaugeCarbon steelMfrs. Std. GaugeGalvanized steelMfrs. Std. GaugeStainless steelU.S. StandardAluminumBrown and Sharpe
3.23916.07 mm··.22945.83 mm
4.22425.69 mm··.20435.19 mm
5.20925.31 mm··.18194.62 mm
6.19434.94 mm··.16204.11 mm
7.17934.55 mm·.18754.76 mm.14433.67 mm
8.16444.18 mm.16814.27 mm.17194.37 mm.12853.26 mm
9.14953.80 mm.15323.89 mm.15633.97 mm.11442.91 mm
10.13453.42 mm.13823.51 mm.14063.57 mm.10192.59 mm
11.11963.04 mm.12333.13 mm.12503.17 mm.09072.30 mm
12.10462.66 mm.10842.75 mm.10942.78 mm.08082.05 mm
13.08972.28 mm.09342.37 mm.09382.38 mm.07201.83 mm
14.07471.90 mm.07851.99 mm.07811.98 mm.06411.63 mm
15.06731.71 mm.07101.80 mm.07031.79 mm.05711.45 mm
16.05981.52 mm.06351.61 mm.06251.59 mm.05081.29 mm
17.05381.37 mm.05751.46 mm.05631.43 mm.04531.15 mm
18.04781.21 mm.05161.31 mm.05001.27 mm.04031.02 mm
19.04181.06 mm.04561.16 mm.04381.11 mm.03590.91 mm
20.03590.91 mm.03961.01 mm.03750.95 mm.03200.81 mm
21.03290.84 mm.03660.93 mm.03440.87 mm.02850.72 mm
22.02990.76 mm.03360.85 mm.03130.80 mm.02530.64 mm
23.02690.68 mm.03060.78 mm.02810.71 mm.02260.57 mm
24.02390.61 mm.02760.70 mm.02500.64 mm.02010.51 mm
25.02090.53 mm.02470.63 mm.02190.56 mm.01790.45 mm
26.01790.45 mm.02170.55 mm.01880.48 mm.01590.40 mm
28.01490.38 mm.01870.47 mm.01560.40 mm.01260.32 mm
30.01200.30 mm.01570.40 mm.01250.32 mm.01000.25 mm

Common aluminum sheet decimal, not gauge

ThicknessinMetricNearest gauge
.02500.64 mm22 ga (.0253)
.03200.81 mm20 ga (.0320)
.04001.02 mm18 ga (.0403)
.05001.27 mm16 ga (.0508)
.06301.60 mm14 ga (.0641)
.08002.03 mm12 ga (.0808)
.09002.29 mm11 ga (.0907)
.10002.54 mm10 ga (.1019)
.12503.17 mm8 ga (.1285)
.16004.06 mm6 ga (.1620)
.19004.83 mmno gauge match
.25006.35 mmno gauge match
NoteAluminum is ordered by decimal thickness, not gauge. Steel gauge numbers come from the Manufacturers' Standard Gauge; stainless uses the U.S. Standard gauge, which runs slightly heavier. Mill tolerance applies to every value here. For a part that cares about thickness, call out the decimal and the tolerance on the print.

Inch tap drills.

Cutting taps, 75 percent thread.

Unified coarse and fine from #0 to 1 inch, with close and free fit clearance drills on the same row.

Inch tap drill chart
ThreadTPIMajorinTap drill75% threadClose fitclearanceFree fitclearance
#0-80 UNF80.06003/64 .04691.19 mm#52 .06351.61 mm#50 .07001.78 mm
#1-64 UNC64.0730#53 .05951.51 mm#48 .07601.93 mm#46 .08102.06 mm
#1-72 UNF72.0730#53 .05951.51 mm#48 .07601.93 mm#46 .08102.06 mm
#2-56 UNC56.0860#50 .07001.78 mm#43 .08902.26 mm#41 .09602.44 mm
#2-64 UNF64.0860#50 .07001.78 mm#43 .08902.26 mm#41 .09602.44 mm
#3-48 UNC48.0990#47 .07851.99 mm#37 .10402.64 mm#35 .11002.79 mm
#3-56 UNF56.0990#45 .08202.08 mm#37 .10402.64 mm#35 .11002.79 mm
#4-40 UNC40.1120#43 .08902.26 mm#32 .11602.95 mm#30 .12853.26 mm
#4-48 UNF48.1120#42 .09352.37 mm#32 .11602.95 mm#30 .12853.26 mm
#5-40 UNC40.1250#38 .10152.58 mm#30 .12853.26 mm#29 .13603.45 mm
#5-44 UNF44.1250#37 .10402.64 mm#30 .12853.26 mm#29 .13603.45 mm
#6-32 UNC32.1380#36 .10652.71 mm#27 .14403.66 mm#25 .14953.80 mm
#6-40 UNF40.1380#33 .11302.87 mm#27 .14403.66 mm#25 .14953.80 mm
#8-32 UNC32.1640#29 .13603.45 mm#18 .16954.31 mm#16 .17704.50 mm
#8-36 UNF36.1640#29 .13603.45 mm#18 .16954.31 mm#16 .17704.50 mm
#10-24 UNC24.1900#25 .14953.80 mm#9 .19604.98 mm#7 .20105.11 mm
#10-32 UNF32.1900#21 .15904.04 mm#9 .19604.98 mm#7 .20105.11 mm
#12-24 UNC24.2160#16 .17704.50 mm#2 .22105.61 mm#1 .22805.79 mm
#12-28 UNF28.2160#14 .18204.62 mm#2 .22105.61 mm#1 .22805.79 mm
1/4-20 UNC20.2500#7 .20105.11 mmF .25706.53 mmH .26606.76 mm
1/4-28 UNF28.2500#3 .21305.41 mmF .25706.53 mmH .26606.76 mm
5/16-18 UNC18.3125F .25706.53 mmP .32308.20 mmQ .33208.43 mm
5/16-24 UNF24.3125I .27206.91 mmP .32308.20 mmQ .33208.43 mm
3/8-16 UNC16.37505/16 .31257.94 mmW .38609.80 mmX .397010.08 mm
3/8-24 UNF24.3750Q .33208.43 mmW .38609.80 mmX .397010.08 mm
7/16-14 UNC14.4375U .36809.35 mm29/64 .453111.51 mm15/32 .468811.91 mm
7/16-20 UNF20.437525/64 .39069.92 mm29/64 .453111.51 mm15/32 .468811.91 mm
1/2-13 UNC13.500027/64 .421910.72 mm33/64 .515613.10 mm17/32 .531213.49 mm
1/2-20 UNF20.500029/64 .453111.51 mm33/64 .515613.10 mm17/32 .531213.49 mm
9/16-12 UNC12.562531/64 .484412.30 mm37/64 .578114.68 mm19/32 .593815.08 mm
9/16-18 UNF18.562533/64 .515613.10 mm37/64 .578114.68 mm19/32 .593815.08 mm
5/8-11 UNC11.625017/32 .531213.49 mm41/64 .640616.27 mm21/32 .656216.67 mm
5/8-18 UNF18.625037/64 .578114.68 mm41/64 .640616.27 mm21/32 .656216.67 mm
3/4-10 UNC10.750021/32 .656216.67 mm49/64 .765619.45 mm25/32 .781219.84 mm
3/4-16 UNF16.750011/16 .687517.46 mm49/64 .765619.45 mm25/32 .781219.84 mm
7/8-9 UNC9.875049/64 .765619.45 mm57/64 .890622.62 mm29/32 .906223.02 mm
7/8-14 UNF14.875013/16 .812520.64 mm57/64 .890622.62 mm29/32 .906223.02 mm
1-8 UNC81.00007/8 .875022.22 mm1-1/64 1.015625.80 mm1-1/32 1.031226.19 mm
1-12 UNF121.000059/64 .921923.42 mm1-1/64 1.015625.80 mm1-1/32 1.031226.19 mm
How to read itTap drill gives about 75 percent of full thread, the usual shop target. Close fit clearance holes are for located hardware, free fit for easy assembly. Decimals are nominal drill sizes; the hole a drill actually cuts runs a little larger.

Metric tap drills.

M1.6 to M24, coarse and fine.

Tap drill, close and medium clearance, and the nearest inch drill for when that is what is in the cabinet.

Metric tap drill chart
ThreadPitchmmMajormmTap drill75% threadNearest inch drillClose fitclearanceMedium fitclearance
M1.6 x 0.350.351.61.25 mm0.0492 in3/64 .04691.19 mm1.7 mm1.8 mm
M2 x 0.40.402.01.60 mm0.0630 in1/16 .06251.59 mm2.2 mm2.4 mm
M2.5 x 0.450.452.52.05 mm0.0807 in#46 .08102.06 mm2.7 mm2.9 mm
M3 x 0.50.503.02.50 mm0.0984 in#40 .09802.49 mm3.2 mm3.4 mm
M3.5 x 0.60.603.52.90 mm0.1142 in#33 .11302.87 mm3.7 mm3.9 mm
M4 x 0.70.704.03.30 mm0.1299 in#30 .12853.26 mm4.3 mm4.5 mm
M5 x 0.80.805.04.20 mm0.1654 in#19 .16604.22 mm5.3 mm5.5 mm
M6 x 1.01.006.05.00 mm0.1969 in#9 .19604.98 mm6.4 mm6.6 mm
M8 x 1.251.258.06.80 mm0.2677 inH .26606.76 mm8.4 mm9.0 mm
M8 x 1.0 fine1.008.07.00 mm0.2756 inJ .27707.04 mm8.4 mm9.0 mm
M10 x 1.51.5010.08.50 mm0.3346 inQ .33208.43 mm10.5 mm11.0 mm
M10 x 1.25 fine1.2510.08.80 mm0.3465 inS .34808.84 mm10.5 mm11.0 mm
M10 x 1.0 fine1.0010.09.00 mm0.3543 inT .35809.09 mm10.5 mm11.0 mm
M12 x 1.751.7512.010.20 mm0.4016 inY .404010.26 mm13.0 mm13.5 mm
M12 x 1.5 fine1.5012.010.50 mm0.4134 inZ .413010.49 mm13.0 mm13.5 mm
M12 x 1.25 fine1.2512.010.80 mm0.4252 in27/64 .421910.72 mm13.0 mm13.5 mm
M14 x 2.02.0014.012.00 mm0.4724 in15/32 .468811.91 mm15.0 mm15.5 mm
M14 x 1.5 fine1.5014.012.50 mm0.4921 in31/64 .484412.30 mm15.0 mm15.5 mm
M16 x 2.02.0016.014.00 mm0.5512 in35/64 .546913.89 mm17.0 mm17.5 mm
M16 x 1.5 fine1.5016.014.50 mm0.5709 in37/64 .578114.68 mm17.0 mm17.5 mm
M18 x 2.52.5018.015.50 mm0.6102 in39/64 .609415.48 mm19.0 mm20.0 mm
M20 x 2.52.5020.017.50 mm0.6890 in11/16 .687517.46 mm21.0 mm22.0 mm
M20 x 1.5 fine1.5020.018.50 mm0.7283 in47/64 .734418.65 mm21.0 mm22.0 mm
M24 x 3.03.0024.021.00 mm0.8268 in53/64 .828121.03 mm25.0 mm26.0 mm
How to read itCoarse pitch is the default; fine pitches are marked. The nearest inch drill column is for when the metric drill is not in the cabinet. Check the thread percentage it gives you in the tap drill finder before you commit.

Helical inserts.

STI tap drills for wire thread inserts.

Oversize holes for helical wire inserts in soft metals and repaired threads. Inch and metric.

Helical insert tap drills

Inch unified coarse and fine

Threadinsert sizeSTI tap drill
#2-56#44 .08602.18 mm
#4-40#33 .11302.87 mm
#4-48#32 .11602.95 mm
#6-32#26 .14703.73 mm
#6-40#28 .14053.57 mm
#8-32#17 .17304.39 mm
#8-36#18 .16954.31 mm
#10-24#5 .20555.22 mm
#10-32#6 .20405.18 mm
1/4-2017/64 .26566.75 mm
1/4-28G .26106.63 mm
5/16-18Q .33208.43 mm
5/16-2421/64 .32818.33 mm
3/8-16X .397010.08 mm
3/8-2425/64 .39069.92 mm
7/16-1429/64 .453111.51 mm
7/16-2029/64 .453111.51 mm
1/2-1333/64 .515613.10 mm
1/2-2033/64 .515613.10 mm
9/16-1237/64 .578114.68 mm
9/16-1837/64 .578114.68 mm
5/8-1141/64 .640616.27 mm
5/8-1841/64 .640616.27 mm
3/4-1049/64 .765619.45 mm
3/4-1649/64 .765619.45 mm
7/8-957/64 .890622.62 mm
1-81-1/64 1.015625.80 mm

Metric coarse

Threadinsert sizeSTI tap drillNearest inch drill
M3 x 0.53.20 mm0.1260 in1/8 .1250
M4 x 0.74.20 mm0.1654 in#19 .1660
M5 x 0.85.20 mm0.2047 in#6 .2040
M6 x 1.06.30 mm0.2480 inE .2500
M8 x 1.258.40 mm0.3307 inQ .3320
M10 x 1.510.50 mm0.4134 inZ .4130
M12 x 1.7512.50 mm0.4921 in31/64 .4844
M14 x 2.014.50 mm0.5709 in37/64 .5781
M16 x 2.016.50 mm0.6496 in21/32 .6562
M20 x 2.520.75 mm0.8169 in13/16 .8125
CautionThese holes are oversize on purpose. They take an STI tap for the same thread, never a standard tap. Insert makers publish their own drill sizes and they vary slightly by brand and tolerance class. Verify against the data for the insert you stock before cutting.

Form taps.

Roll form drills, 65 percent thread.

No chips and a stronger thread, but the hole size matters more. Drill = major minus 0.442 x pitch, then the nearest standard drill.

Form tap drill chart

Inch 65 percent thread

ThreadTPIMajorin65% drillcalculatedUse this drillnearest, inch or metricThread you get
#4-4040.1120.1009#38 .10152.58 mm62%
#6-3232.1380.12421/8 .12503.17 mm61%
#8-3232.1640.1502#25 .14953.80 mm68%
#10-2424.1900.171611/64 .17194.37 mm64%
#10-3232.1900.1762#16 .17704.50 mm61%
1/4-2020.2500.2279#1 .22805.79 mm65%
1/4-2828.2500.234215/64 .23445.95 mm64%
5/16-1818.3125.28797.30 mm .287466%
5/16-2424.3125.2941M .29507.49 mm62%
3/8-1616.3750.3474S .34808.84 mm64%
3/8-2424.3750.3566T .35809.09 mm60%
7/16-1414.4375.405913/32 .406210.32 mm64%
7/16-2020.4375.4154Z .413010.49 mm72%
1/2-1313.5000.466011.80 mm .464668%
1/2-2020.5000.477912.10 mm .476469%

Metric 65 percent thread

ThreadPitchmmMajormm65% drillcalculatedUse this drillnearest, metric or inchThread you get
M3 x 0.50.503.02.782.80 mm.1102 in59%
M4 x 0.70.704.03.693.70 mm.1457 in63%
M5 x 0.80.805.04.65#14 .18204.62 mm69%
M6 x 1.01.006.05.567/32 .21885.56 mm65%
M8 x 1.251.258.07.457.40 mm.2913 in71%
M10 x 1.51.5010.09.34U .36809.35 mm64%
M12 x 1.751.7512.011.2311.20 mm.4409 in67%
The ruleDrill = major diameter minus 0.442 x pitch. That is 65 percent thread, the usual form tap target. We list the nearest standard drill, inch or metric, and the thread percentage it actually gives. Where the nearest drill lands far from 65 percent, ask us or the tap maker for the hole size window.
CautionForm taps make no chips, so blind holes stay clean and the thread is stronger. The trade: the hole size window is tight, and only ductile materials roll well. Aluminum, brass, copper and low carbon steel are good. Stainless works with the right tap and lubricant. Cast iron and hardened steel do not. Confirm with the tap maker's chart.

Drill sizes.

Every standard drill, in order.

Number, letter and fractional drills from #80 to 1 inch, decimal and millimeter, sorted by size so the next one up is always next door.

Drill size chart
DrillInchmm
#80.01350.34
#79.01450.37
1/64.01560.40
#78.01600.41
#77.01800.46
#76.02000.51
#75.02100.53
#74.02250.57
#73.02400.61
#72.02500.64
#71.02600.66
#70.02800.71
#69.02920.74
#68.03100.79
1/32.03120.79
#67.03200.81
#66.03300.84
#65.03500.89
#64.03600.91
#63.03700.94
#62.03800.97
#61.03900.99
#60.04001.02
#59.04101.04
#58.04201.07
#57.04301.09
#56.04651.18
3/64.04691.19
#55.05201.32
#54.05501.40
#53.05951.51
1/16.06251.59
#52.06351.61
#51.06701.70
#50.07001.78
#49.07301.85
#48.07601.93
5/64.07811.98
#47.07851.99
#46.08102.06
#45.08202.08
#44.08602.18
#43.08902.26
DrillInchmm
#42.09352.37
3/32.09382.38
#41.09602.44
#40.09802.49
#39.09952.53
#38.10152.58
#37.10402.64
#36.10652.71
7/64.10942.78
#35.11002.79
#34.11102.82
#33.11302.87
#32.11602.95
#31.12003.05
1/8.12503.17
#30.12853.26
#29.13603.45
#28.14053.57
9/64.14063.57
#27.14403.66
#26.14703.73
#25.14953.80
#24.15203.86
#23.15403.91
5/32.15623.97
#22.15703.99
#21.15904.04
#20.16104.09
#19.16604.22
#18.16954.31
11/64.17194.37
#17.17304.39
#16.17704.50
#15.18004.57
#14.18204.62
#13.18504.70
3/16.18754.76
#12.18904.80
#11.19104.85
#10.19354.91
#9.19604.98
#8.19905.05
#7.20105.11
DrillInchmm
13/64.20315.16
#6.20405.18
#5.20555.22
#4.20905.31
#3.21305.41
7/32.21885.56
#2.22105.61
#1.22805.79
A.23405.94
15/64.23445.95
B.23806.05
C.24206.15
D.24606.25
E.25006.35
1/4.25006.35
F.25706.53
G.26106.63
17/64.26566.75
H.26606.76
I.27206.91
J.27707.04
K.28107.14
9/32.28127.14
L.29007.37
M.29507.49
19/64.29697.54
N.30207.67
5/16.31257.94
O.31608.03
P.32308.20
21/64.32818.33
Q.33208.43
R.33908.61
11/32.34388.73
S.34808.84
T.35809.09
23/64.35949.13
U.36809.35
3/8.37509.52
V.37709.58
W.38609.80
25/64.39069.92
X.397010.08
DrillInchmm
Y.404010.26
13/32.406210.32
Z.413010.49
27/64.421910.72
7/16.437511.11
29/64.453111.51
15/32.468811.91
31/64.484412.30
1/2.500012.70
33/64.515613.10
17/32.531213.49
35/64.546913.89
9/16.562514.29
37/64.578114.68
19/32.593815.08
39/64.609415.48
5/8.625015.88
41/64.640616.27
21/32.656216.67
43/64.671917.07
11/16.687517.46
45/64.703117.86
23/32.718818.26
47/64.734418.65
3/4.750019.05
49/64.765619.45
25/32.781219.84
51/64.796920.24
13/16.812520.64
53/64.828121.03
27/32.843821.43
55/64.859421.83
7/8.875022.22
57/64.890622.62
29/32.906223.02
59/64.921923.42
15/16.937523.81
61/64.953124.21
31/32.968824.61
63/64.984425.00
11.000025.40
LegendNumber drills #80 to #1, letter drills A to Z, fractional drills 1/64 to 1 inch, all in order of size. Metric values are exact conversions of the nominal inch size.

Hole and hardware.

Countersinks, counterbores, PEM holes, pipe taps.

The hole sizes that go with the hardware: flat heads, socket heads, self clinching nuts, studs and standoffs, and NPT.

Hole and hardware charts

Countersinks theoretical sharp Ø

ScrewFlat head machine screwASME B18.6.3, 82°Flat socket head cap screwASME B18.3, 82°
#2.17204.37 mm.19705.00 mm
#3.19905.05 mm.22605.74 mm
#4.22505.71 mm.25506.48 mm
#5.25206.40 mm.28107.14 mm
#6.27907.09 mm.30707.80 mm
#8.33208.43 mm.35909.12 mm
#10.38509.78 mm.411010.44 mm
#12.438011.13 mm·
1/4.507012.88 mm.531013.49 mm
5/16.635016.13 mm.656016.66 mm
3/8.762019.35 mm.781019.84 mm
7/16.812020.62 mm.844021.44 mm
1/2.875022.22 mm.938023.83 mm
5/81.125028.57 mm1.188030.18 mm
3/41.375034.92 mm1.438036.53 mm

Metric countersinks 90°

ScrewFlat socket headISO 10642, 90°
M36.72 mm0.265 in
M48.96 mm0.353 in
M511.20 mm0.441 in
M613.44 mm0.529 in
M817.92 mm0.706 in
M1022.40 mm0.882 in
M1226.88 mm1.058 in
M1633.60 mm1.323 in
M2040.32 mm1.587 in
Countersink calloutThe diameters are the theoretical sharp corner of the head. A head sits flush when the countersink Ø is at or a few thousandths over this value. Typical callout: ⌵ Ø.385 X 82°. Flat head machine screws and flat socket heads have different head diameters, so pick the right column.

Counterbores, inch socket head cap screws

ScrewSHCSCounterbore ØDepthhead heightClose fit holeFree fit hole
#2.18804.78 mm.08602.18 mm#43 .08902.26 mm#41 .09602.44 mm
#4.21905.56 mm.11202.84 mm#32 .11602.95 mm#30 .12853.26 mm
#5.25006.35 mm.12503.17 mm#30 .12853.26 mm#29 .13603.45 mm
#6.28107.14 mm.13803.51 mm#27 .14403.66 mm#25 .14953.80 mm
#8.31207.92 mm.16404.17 mm#18 .16954.31 mm#16 .17704.50 mm
#10.37509.52 mm.19004.83 mm#9 .19604.98 mm#7 .20105.11 mm
1/4.438011.13 mm.25006.35 mmF .25706.53 mmH .26606.76 mm
5/16.531013.49 mm.31207.92 mmP .32308.20 mmQ .33208.43 mm
3/8.625015.88 mm.37509.52 mmW .38609.80 mmX .397010.08 mm
7/16.719018.26 mm.438011.13 mm29/64 .453111.51 mm15/32 .468811.91 mm
1/2.812020.62 mm.500012.70 mm33/64 .515613.10 mm17/32 .531213.49 mm
5/81.000025.40 mm.625015.88 mm41/64 .640616.27 mm21/32 .656216.67 mm
3/41.188030.18 mm.750019.05 mm49/64 .765619.45 mm25/32 .781219.84 mm
11.625041.27 mm1.000025.40 mm1-1/64 1.015625.80 mm1-1/32 1.031226.19 mm

Counterbores, metric socket head cap screws

ScrewSHCSCounterbore ØDepthhead heightClose fit holeMedium fit hole
M36.5 mm0.256 in3.0 mm3.2 mm3.4 mm
M48.0 mm0.315 in4.0 mm4.3 mm4.5 mm
M510.0 mm0.394 in5.0 mm5.3 mm5.5 mm
M611.0 mm0.433 in6.0 mm6.4 mm6.6 mm
M815.0 mm0.591 in8.0 mm8.4 mm9.0 mm
M1018.0 mm0.709 in10.0 mm10.5 mm11.0 mm
M1220.0 mm0.787 in12.0 mm13.0 mm13.5 mm
M1626.0 mm1.024 in16.0 mm17.0 mm17.5 mm
M2033.0 mm1.299 in20.0 mm21.0 mm22.0 mm
Counterbore calloutDepth equals the head height, so the head sits flush. Add a few thousandths if a washer or coating is in play. Typical callout: Ø.2660 THRU, ⌴ Ø.438 ⬇ .250.

PEM self clinching hardware hole size in sheet

Nuts, S / SS / CLS / CLSS inch

Thread (code)Hole in sheetinMin sheet -0inMin sheet -1inMin sheet -2inMin sheet -3in
#4-40 (440).1660+.003 / -.000.0300.0400.0560.0900
#6-32 (632).1875+.003 / -.000.0300.0400.0560.0900
#8-32 (832).2130+.003 / -.000.0300.0400.0560.0900
#10-32 (032).2500+.003 / -.000.0300.0400.0560.0900
1/4-20 (0420).3440+.003 / -.000.0470.0560.0900.1250
5/16-18 (0518).4130+.003 / -.000·.0560.0900.1250
3/8-16 (0616).5000+.003 / -.000·.0900.1250.2500

Nuts, S / SS / CLS / CLSS metric

ThreadHole in sheetmmMin sheet -00mmMin sheet -0mmMin sheet -1mmMin sheet -2mm
M34.22 mm+0.08·0.801.001.40
M45.41 mm+0.08·0.801.001.40
M56.35 mm+0.08·0.801.001.40
M68.75 mm+0.080.921.201.402.29
M810.50 mm+0.08··1.402.29
M1014.00 mm+0.08··2.293.18

Flush head studs, FH / FHS inch and metric

ThreadFH / FHSHole in sheetinMin sheetin
#4-40.1110+.003 / -.000.0400
#6-32.1370+.003 / -.000.0400
#8-32.1630+.003 / -.000.0400
#10-32.1890+.003 / -.000.0400
1/4-20.2490+.003 / -.000.0620
5/16-18.3110+.003 / -.000.0930
ThreadFH / FHSHole in sheetmmMin sheetmm
M33.00 mm+0.081.0 mm
M3.53.50 mm+0.081.0 mm
M44.00 mm+0.081.0 mm
M55.00 mm+0.081.0 mm
M66.00 mm+0.081.6 mm
M88.00 mm+0.082.4 mm

Thru threaded standoffs, SO / SOS / SOA inch and metric

ThreadSO / SOS / SOAHole in sheetinMin sheetin
#4-40.1660+.003 / -.000.0400
#6-32.2130+.003 / -.000.0400
#8-32.2810+.003 / -.000.0500
#10-32.2810+.003 / -.000.0500
ThreadSO / SOS / SOAHole in sheetmmMin sheetmm
M34.22 mm+0.08 / -0.131.00 mm
M3.55.41 mm+0.08 / -0.131.00 mm
M47.14 mm+0.08 / -0.131.27 mm
M57.14 mm+0.08 / -0.131.27 mm
CautionHole sizes and minimum sheet thickness are from the PennEngineering data sheets for the S, SS, CLS, FH, FHS and SO families. Other brands and other families (stainless sheet types, miniature, floating) differ. Hole size is a maximum as well as a minimum: oversize and the hardware spins. Verify the exact part number against its data sheet before you cut.

Pipe tap drills NPT

Pipe threadNPTTPITap drillno reamer
1/16-2727D .24606.25 mm
1/8-2727R .33908.61 mm
1/4-18187/16 .437511.11 mm
3/8-181837/64 .578114.68 mm
1/2-141423/32 .718818.26 mm
3/4-141459/64 .921923.42 mm
1-11.511.51-5/32 1.156229.37 mm
1-1/4-11.511.51-1/2 1.500038.10 mm
1-1/2-11.511.51-47/64 1.734444.05 mm
2-11.511.52-7/32 2.218856.36 mm
Pipe threadsDrill, then taper ream for the cleanest NPT thread; the drill sizes here are for tapping without a reamer. Tap depth sets the fit: gage with an L1 ring or plug. NPTF (dryseal) uses the same drills and needs a reamer.

Tolerances and finish.

What the print means when it says nothing.

ISO 2768 general tolerances, surface roughness with the process behind each number, thread classes, and our own laser cut tolerance guide.

Tolerance and finish references

ISO 2768-1 general tolerances linear dimensions, mm

Class0.5 to 3mm3 to 6mm6 to 30mm30 to 120mm120 to 400mm400 to 1000mm1000 to 2000mm2000 to 4000mm
f (fine)±0.05±0.05±0.1±0.15±0.2±0.3±0.5·
m (medium)±0.1±0.1±0.2±0.3±0.5±0.8±1.2±2
c (coarse)±0.2±0.3±0.5±0.8±1.2±2±3±4
v (very coarse)·±0.5±1±1.5±2.5±4±6±8

External radii and chamfer heights mm

Class0.5 to 3mm3 to 6mmover 6mm
f and m±0.2±0.5±1
c and v±0.4±1±2

Angular by length of the shorter side

Classup to 10mm, shorter side10 to 50mm, shorter side50 to 120mm, shorter side120 to 400mm, shorter sideover 400mm, shorter side
f and m±1°±0°30'±0°20'±0°10'±0°5'
c±1°30'±1°±0°30'±0°15'±0°10'
v±3°±2°±1°±0°30'±0°20'
How to call it outISO 2768-mK on the title block means medium linear tolerances and class K geometric tolerances for everything not dimensioned otherwise. Inch prints usually carry a block instead: .X ±.030 .XX ±.010 .XXX ±.005 ANGLES ±0°30'. Both are fine. Say which.

ISO 2768-2 general geometric tolerances mm

Straightness and flatness by length

Classup to 10mm10 to 30mm30 to 100mm100 to 300mm300 to 1000mm1000 to 3000mm
H0.020.050.10.20.30.4
K0.050.10.20.40.60.8
L0.10.20.40.81.21.6

Perpendicularity by shorter side

Classup to 100mm100 to 300mm300 to 1000mm1000 to 3000mm
H0.20.30.40.5
K0.40.60.81
L0.611.52

Symmetry by length

Classup to 100mm100 to 300mm300 to 1000mm1000 to 3000mm
H0.50.50.50.5
K0.60.60.81
L0.611.52

Circular runout all sizes

ClassCircular runoutmm
H0.1
K0.2
L0.5

Surface roughness Ra, with the process that makes it

GradeISO 1302RaµmRaµinTypical processWhere you see it
N12502000Flame cutting, rough sawingRaw stock faces
N11251000Sand casting, hot rolling, rough turningCasting skin, hot rolled plate
N1012.5500Rough milling, sawing, laser cut edge as cut (thick)Non-critical faces
N96.3250Milling and turning, roughing passes, laser cut edge as cutDefault when nothing is specified
N83.2125Milling, turning, drilling, laser cut edge deburredThe common "125" callout on machined parts
N71.663Fine milling and turning, reaming, boringSealing faces, bearing shoulders, cosmetic machined surfaces
N60.832Fine turning, fine boring, grinding, reamingStatic seal faces, press fits
N50.416Grinding, honing, fine reamingDynamic seals, bearing journals
N40.28Honing, lapping, polishingGage surfaces, hydraulic spools
N30.14Lapping, superfinishingValve seats, optical mounts
N20.052Lapping, polishingMirror finishes
N10.0251SuperfinishingGage blocks
On the printRa 125 µin (3.2 µm) is the common machined default. Ra 63 is a fine machined finish without grinding. Below Ra 32 you are paying for grinding, honing or lapping, so call it out only where a seal or bearing needs it.

Thread class guide unified and metric

ClassFitAllowanceUse
1A / 1BLooseYes (1A)Quick assembly, dirty or coated threads, field hardware. Rare on prints.
2A / 2BStandardYes (2A)The commercial default. Most fasteners, most tapped holes. Assumed when the print is silent.
3A / 3BCloseNoneAerospace fasteners, socket set screws, anything that must not rattle. Costs more to gage and hold.
6g / 6HMedium (metric)Yes (6g)The metric default, equivalent to 2A / 2B.
4g6g / 4H5HClose (metric)SmallMetric close fit, equivalent to 3A / 3B.
8g / 7HLoose (metric)YesHot dip galvanized or heavy coated threads.

Laser cut tolerance guide Max Machining, 12 kW fiber

Typical tolerance by thickness

Material thicknessinTypical tolerance
up to .060±.0050±0.13 mm
.061 to .125±.0080±0.20 mm
.126 to .250±.0120±0.30 mm
.251 to .500±.0150±0.38 mm
over .500±.0250±0.64 mm

Minimum hole size 60 percent of thickness

ThicknessinMinimum hole60% of thickness
.0600.03600.91 mm
.1250.07501.90 mm
.1870.11202.84 mm
.2500.15003.81 mm
.3750.22505.71 mm
.5000.30007.62 mm

Edge finish options

Edge finishWhat you get
As cutFastest, lowest cost. Visible edge texture, small burr possible.
DeburredSmooth, safe edges. The most common choice.
TumbledUniform matte, softened edges. A cosmetic step up.
BrushedDirectional grain. Premium appearance for visible panels.
Powder coatedFinal product finish. Durable and corrosion resistant, RAL colors.
Watch forHoles under 60 percent of thickness (drill them after). Expecting a cosmetic edge without specifying one. Tight tolerances on laser-only features: anything tighter than the table gets machined after cutting. Ignoring edge condition on parts that get handled or coated.

Downloads.

Print the card. Hang it by the machine.

Letter size PDFs, one chart each or the whole pack. Plus the DFM checklist, the drawing notes template, the company documents buyers ask for, and how to get files to us.

Shop reference pack

Every chart on this page in one file. Print it, punch it, hang it on the ring by the machine.

PDF · Letter · Rev. Nov 2026

Sheet gauge chart

Gauge to decimal for carbon steel, galvanized, stainless and aluminum. Common aluminum decimals.

PDF · Letter · Rev. Nov 2026

Inch tap drill chart

Unified coarse and fine #0 to 1 inch. 75 percent tap drills with close and free fit clearance drills.

PDF · Letter · Rev. Nov 2026

Metric tap drill chart

M1.6 to M24, coarse and fine. Tap drill, clearance drills and the nearest inch drill.

PDF · Letter · Rev. Nov 2026

Helical insert tap drill chart

STI drill sizes for wire thread inserts, inch and metric, with the caution printed on the card.

PDF · Letter · Rev. Nov 2026

Form tap drill chart

Roll form drills at 65 percent thread, inch and metric, with the thread percentage each drill gives.

PDF · Letter · Rev. Nov 2026

Drill size chart

Number, letter and fractional drills in one ordered list with decimal and millimeter.

PDF · Letter · Rev. Nov 2026

Hole and hardware chart

Countersinks, counterbores, PEM hole sizes and NPT tap drills. Two pages.

PDF · Letter · Rev. Nov 2026

Tolerance and finish chart

ISO 2768 linear, angular and geometric, surface roughness, thread classes, laser tolerance guide. Two pages.

PDF · Letter · Rev. Nov 2026

DFM checklist

Design for manufacturing checks for machined parts and sheet metal. Two pages, one per process.

PDF · Letter · Rev. Nov 2026

Drawing notes template

A title block and the standard notes that make a print quotable: material, finish, edges, tolerance block, Y14.5.

PDF · Letter · Rev. Nov 2026

Company documents

Capability statement

One page for the buyer's file: who we are, what we run, NAICS and PSC codes, registrations. Updated as the shop grows.

PDF

Credit application

For net terms. Fill it in, sign it, and send it back through PreVeil or to sales. We confirm terms before the first order ships.

PDF

01Send us a drawing

Native CAD is best. We also take neutral formats and prints.

  • STEP (.stp, .step)
  • Parasolid (.x_t)
  • SolidWorks (.sldprt)
  • IGES (.igs)
  • DXF or DWG for flat parts
  • PDF prints with revision

02Controlled data

ITAR and CUI files never ride plain email. Create a free PreVeil account, then share with Info@MaxMachining.com. Encrypted end to end, and it keeps the audit trail both sides need.

03Customer portal

Open orders, due dates, shipments and documents live in the customer portal. Ask your sales contact for a login if you do not have one.